Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Join us on Facebook: Search for 'ConcoursMustang' Private group!
Home
Help
Login
Register
ConcoursMustang Forums
»
1st Generation 1964 1/2 - 1973 - Questions & general discussions that apply to a specific year
»
1970 Mustang
»
Topic:
Rubber Shield Fasteners
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Rubber Shield Fasteners (Read 2180 times)
imnutz66
Newbie
Posts: 18
Rubber Shield Fasteners
«
on:
April 07, 2010, 07:54:32 AM »
Can someone tell me what fastener was used to install the rubber flap above the rear license plate on 70's? I have the holes there, but the flap was removed by PO along with the fasteners
Thanks, Joe
Logged
70 Mach 1 351C 4V 4Speed
Dearborn
Born October, 1969
Bill73Ragtop
Newbie
Posts: 7
Re: Rubber Shield Fasteners
«
Reply #1 on:
April 07, 2010, 09:33:56 AM »
My 69 vert had philips head screws. It was original as far as I could tell. I replaced them with stainless screws when re-assembling.
Logged
cobrajetchris
Sr. Member
Posts: 335
Re: Rubber Shield Fasteners
«
Reply #2 on:
April 07, 2010, 11:44:07 AM »
The ones I have seen are all round head Phillips screws that are very short and have a black phosphate type coating, I am sure AMK fasteners would have them.
Logged
CHRIS KNOBBE
69 MUSTANG COUPE, DEARBORN BUILT 06/10/69 OWNED SINCE 1978
70 BOSS 302 MUSTANG, DEARBORN BUILT 10/24/69 OWNED SINCE 1987
69 R CODE MACH1 AUTO, DEARBORN BUILT 10/10/68 OWNED SINCE 2006
69 R CODE MACH1 4 SPEED (factory black) SAN JOSE BUILT 12/30/68 OWNED SINCE 2007
imnutz66
Newbie
Posts: 18
Re: Rubber Shield Fasteners
«
Reply #3 on:
April 07, 2010, 12:23:59 PM »
Thanks for the info, were they round head for sure and not pan head?
Logged
70 Mach 1 351C 4V 4Speed
Dearborn
Born October, 1969
J_Speegle
Administrator
Hero Member
Posts: 24220
Re: Rubber Shield Fasteners
«
Reply #4 on:
April 07, 2010, 09:08:43 PM »
Only seen round head phillips used
Logged
Jeff Speegle
Anything worth doing is worth doing concours
rockhouse66
Hero Member
Posts: 930
Re: Rubber Shield Fasteners
«
Reply #5 on:
April 08, 2010, 10:57:21 AM »
This is from a 1969 Dearborn car. I am sure the original finish was P&O.
Logged
Jim
'66 GT FB
imnutz66
Newbie
Posts: 18
Re: Rubber Shield Fasteners
«
Reply #6 on:
April 08, 2010, 11:23:42 AM »
That picture is great, I actually have a handful of screws identical to that - if I can just remember exactly where they are!
Logged
70 Mach 1 351C 4V 4Speed
Dearborn
Born October, 1969
Bob Gaines
Global Moderator
Hero Member
Posts: 8985
Re: Rubber Shield Fasteners
«
Reply #7 on:
April 08, 2010, 11:34:50 PM »
Those screws look like the screws at the bottom that hold the interior dash trim pieces of the two in the center (ether side of radio)and two outer trim panels on a 69. AMK sells them. Bob
Logged
Bob Gaines,Shelby enthusiast, Shelby collector , Shelby concours judge SAAC,MCA,Mid America Shelby
Print
Pages: [
1
]
Go Up
« previous
next »
ConcoursMustang Forums
»
1st Generation 1964 1/2 - 1973 - Questions & general discussions that apply to a specific year
»
1970 Mustang
»
Topic:
Rubber Shield Fasteners