Author Topic: Staggered Shock Plate & Rear Brackets  (Read 1872 times)

Offline 13Outlaw

  • Full Member
  • ***
  • Posts: 123
Staggered Shock Plate & Rear Brackets
« on: August 03, 2016, 09:50:58 PM »
Hello all, been away for awhile and trying to get going back on the car. I got the new inner/outer fender wells in, full quarters in, etc. Does anyone have the measurements of exactly where to cut the staggered shock hole? Also, I was needing the measurements for all the brackets that go on the wheel wells, and rear seat area. I had all the measurements written down and simply can not find them. 1969 R-Code 4 Speed. Thanks for any help.
Shane
1969 Mach 1 R-Code 4-Speed (Dearborn built Jan 69)
1992 GT 5.0 5-Speed
2003 Cobra
2013 Shelby GT500

Offline 13Outlaw

  • Full Member
  • ***
  • Posts: 123
Re: Staggered Shock Plate & Rear Brackets
« Reply #1 on: August 04, 2016, 12:07:25 AM »
I should mention I changed the rear transition pan and therefore there is no hole cut for the Staggered Shock. Thanks
1969 Mach 1 R-Code 4-Speed (Dearborn built Jan 69)
1992 GT 5.0 5-Speed
2003 Cobra
2013 Shelby GT500

Offline 7Lscjracer

  • Hero Member
  • *****
  • Posts: 522
Re: Staggered Shock Plate & Rear Brackets
« Reply #2 on: August 04, 2016, 01:15:59 AM »
http://sancospecialties.com/stagger.htm

I would contact Forrest, I'm sure he could help you out
69 Mach 1 San Jose Nov. 68 build
Bought May '81, sold Sept '20

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24173
Re: Staggered Shock Plate & Rear Brackets
« Reply #3 on: August 04, 2016, 01:51:37 AM »
Don't have either of the 69's I have with staggered rear shocks close by so can't take the measurements (no 69's at home currently) . Too mad they were not measured or a template made before those panels were replaced on your car.
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline 13Outlaw

  • Full Member
  • ***
  • Posts: 123
Re: Staggered Shock Plate & Rear Brackets
« Reply #4 on: August 04, 2016, 08:33:13 AM »
Thanks all! Jeff I did take measurements, but I can not find the binder I had them in. I did snap a picture wit my phone, but that isn't a lot of help obviously, just for the general area. Thanks again.
1969 Mach 1 R-Code 4-Speed (Dearborn built Jan 69)
1992 GT 5.0 5-Speed
2003 Cobra
2013 Shelby GT500

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24173
Re: Staggered Shock Plate & Rear Brackets
« Reply #5 on: August 04, 2016, 02:47:07 PM »
Thanks all! Jeff I did take measurements, but I can not find the binder I had them in. I did snap a picture wit my phone, but that isn't a lot of help obviously, just for the general area. Thanks again.

Ouch  - feel for you. Planned ahead and it didn't work out. Happens to all of us
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline 13Outlaw

  • Full Member
  • ***
  • Posts: 123
Re: Staggered Shock Plate & Rear Brackets
« Reply #6 on: August 05, 2016, 01:19:47 AM »
Yea thanks again, I'll let you all know how it turns out.
1969 Mach 1 R-Code 4-Speed (Dearborn built Jan 69)
1992 GT 5.0 5-Speed
2003 Cobra
2013 Shelby GT500