Author Topic: '65 ALTERNATOR CONDERSOR WANTED  (Read 2672 times)

Offline C5ZZKGT

  • Gold Level Subscriber
  • Hero Member
  • *****
  • Posts: 787
'65 ALTERNATOR CONDERSOR WANTED
« on: June 13, 2011, 09:00:27 PM »
C5TA-18827-A is what I understand the part number is, either a GOOD used, NOS or CORRECT Reproduction-(if they exist)  THANKS!!!!

Offline Twilight65

  • Gold Level Subscriber
  • Sr. Member
  • *****
  • Posts: 380
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #1 on: June 14, 2011, 09:47:54 AM »
Rick, I've heard you can get these sometime from deadnutson. You may try calling them.
Dave

http://www.deadnutson.com/page/page/2958685.htm
65 Coupe Dearborn Scheduled Build July 9,1965 289/C4
66 Sprint Conv. Dearborn Scheduled Build May 13, 1966 200/C4

Offline C5ZZKGT

  • Gold Level Subscriber
  • Hero Member
  • *****
  • Posts: 787
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #2 on: June 14, 2011, 10:15:06 AM »
Dave, Thanks!!  I sent Jack an Email, Rick

Offline C5ZZKGT

  • Gold Level Subscriber
  • Hero Member
  • *****
  • Posts: 787
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #3 on: July 09, 2011, 07:03:36 AM »
Bump......still looking......

Offline C5ZZKGT

  • Gold Level Subscriber
  • Hero Member
  • *****
  • Posts: 787
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #4 on: July 09, 2011, 04:45:03 PM »
I actually found one in my parts stash-kinda ugly-how can I refinish it? I've cleaned it up with some steel wool but it needs more before I put it on my car.

Offline Bob Gaines

  • Global Moderator
  • Hero Member
  • ****
  • Posts: 8950
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #5 on: July 09, 2011, 05:17:15 PM »
I actually found one in my parts stash-kinda ugly-how can I refinish it? I've cleaned it up with some steel wool but it needs more before I put it on my car.
If you had one of Eastwoods inexpensive zinc plating kits you could hook it and dip it in and about 3 minutes later it is plated. You can adjust the sheen with a light rub from a towel to a more abrasive extra fine steel wool. Usually I buff it with a course towel and it is good to go. You can of course send in to your local  plater with a minimum order and hope they don't break the wire off. I hope this helps . Bob
Bob Gaines,Shelby enthusiast, Shelby collector , Shelby concours judge SAAC,MCA,Mid America Shelby

Offline C5ZZKGT

  • Gold Level Subscriber
  • Hero Member
  • *****
  • Posts: 787
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #6 on: July 10, 2011, 01:22:07 PM »
Thanks Bob!! This does help, I'll check out the Eastwood kit.

Offline C5ZZKGT

  • Gold Level Subscriber
  • Hero Member
  • *****
  • Posts: 787
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #7 on: August 08, 2011, 02:30:42 PM »
Still looking for a NICE one.
I've got the old one I had refinished the best I could and installed it-looks ok, but the connector has been replaced with a generic one and the wire is actually too short to plug in right.........Please check around for me, I'd sure appreciate it. Thanks!!

Offline Andrew@MagMustangs

  • Sr. Member
  • ****
  • Posts: 334
  • MagMustangs: Original Parts for 64 1/2-73 Mustangs
    • MagMustangs
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #8 on: August 26, 2011, 01:56:52 PM »
If you are still looking for one, I just listed one in My Ebay Store. It is a Good Original. Andrew

http://stores.ebay.com/MagMustangs
MagMustangs: Vintage Mustang Enthusiasts. We have Original Factory Parts for 1964 1/2-1973 Ford Mustang.   Like Us On Facebook. https://www.facebook.com/MagMustangs

Offline rodster

  • Hero Member
  • *****
  • Posts: 1011
Re: '65 ALTERNATOR CONDERSOR WANTED
« Reply #9 on: August 27, 2011, 11:08:56 PM »

I'll look around and if I find one you can have it for the price of shipping....
1965 Dearborn Mustang Coupe
Raven Black - Palomino Pony
1967 Dearborn Mustang Conv.
Wimbeldon White - Red
1984 SVO - 2A