Author Topic: Fuse removal  (Read 2456 times)

Offline austexstang

  • Full Member
  • ***
  • Posts: 125
Fuse removal
« on: January 31, 2017, 03:49:32 PM »
Hello Everyone:

What kind of tool/device do you recommend to remove the fuses in a '65 Coupe?  They seem a little difficult to replace and I don't want to break one.

Thanks 

Offline ChrisV289

  • Hero Member
  • *****
  • Posts: 1956
Re: Fuse removal
« Reply #1 on: January 31, 2017, 04:01:02 PM »
Could always disconnect the battery and use a small flat head screw driver
Chris
1965 Honey Gold Fastback (SJ 10/29/64)
1965 Caspian Blue Fastback (SJ 06/03/65)
2009 V6 Mustang Coupe

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24173
Re: Fuse removal
« Reply #2 on: January 31, 2017, 04:13:03 PM »
I've most often used one of those cheap pick tools with the curved end. Work it into and behind the metal end and swing one end out of the receiver to 90 degrees from the fuse black then pull the fuse out.

Just what has worked for me
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline 67gtasanjose

  • Hero Member
  • *****
  • Posts: 5084
  • "Take the MUSTANG PLEDGE"
Re: Fuse removal
« Reply #3 on: January 31, 2017, 04:14:15 PM »
+1
don't pry on the glass area, use the small screw driver on the end (chromed) area. Some can be difficult.
Richard Urch

1967 (11/2/66, S.J.) GTA Luxury Coupe, 289-4V w/Thermactor Emissions, C-4, Int./Ext. Decor +many options

2005 (04/05) GT Premium Convertible, Windveil Blue, Parchment Top w/Med. Parchment interior,  Roush Body Appointments

Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7098
Re: Fuse removal
« Reply #4 on: January 31, 2017, 04:23:32 PM »
Use this link to get an idea of what a fuse removal looks like - https://www.amazon.com/Littelfuse-097023BP-Tri-Puller-Fuse-Puller/dp/B000BOB3TW/ref=sr_1_1?s=automotive&ie=UTF8&qid=1485893915&sr=1-1&keywords=fuse+removal+tool
use the small screw driver on the end (chromed) area. Some can be difficult.
Could always disconnect the battery and use a small flat head screw driver
DO NOT USE A METAL TOOL TO REMOVE A FUSE. If you are not familiar with servicing electrical or electronics equipment, do disconnect the battery.
Jim
I promise to be politically correct in all my posts to keep the BBBB from vociferating.

Offline austexstang

  • Full Member
  • ***
  • Posts: 125
Re: Fuse removal
« Reply #5 on: January 31, 2017, 04:34:17 PM »
Thank you all for the ideas/suggestions...  and YES, step #1 is always disconnecting the battery....

Offline midlife

  • Wiring Guru---let me check your shorts!
  • Global Moderator
  • Hero Member
  • ****
  • Posts: 2155
    • Midlife Harness Restorations
Re: Fuse removal
« Reply #6 on: January 31, 2017, 10:53:00 PM »
Use this link to get an idea of what a fuse removal looks like - https://www.amazon.com/Littelfuse-097023BP-Tri-Puller-Fuse-Puller/dp/B000BOB3TW/ref=sr_1_1?s=automotive&ie=UTF8&qid=1485893915&sr=1-1&keywords=fuse+removal+toolDO NOT USE A METAL TOOL TO REMOVE A FUSE. If you are not familiar with servicing electrical or electronics equipment, do disconnect the battery.
Jim

I use a very close variant of that tool.  Many fuses become one with the clips when rusted or corroded, and even then, they will break on me.  Disconnect the battery and use a small jeweler's screwdriver to wedge a space between the fuse and the clip on all four points and then use the tool to pry the fuse out.  Unfortunately, that tool is too wide for 7.5 and 2.5/4.0 amp fuses. 
Midlife Harness Restorations - http://midlifeharness.com

Offline austexstang

  • Full Member
  • ***
  • Posts: 125
Re: Fuse removal
« Reply #7 on: February 01, 2017, 04:00:10 PM »
Nice...   thank you