Author Topic: re-painting 66' styled wheels  (Read 807 times)

Offline Hipo giddyup

  • Hero Member
  • *****
  • Posts: 1201
  • There is no end to doing right. Giddyup!!!
re-painting 66' styled wheels
« on: August 14, 2017, 09:58:45 AM »
  Does anyone know if they make a template to mask off the 66' styled wheel in order to repaint the dark charcoal color?? I have no probelm hand taping them but could make better use of my time than spending a couple hours of masking.  ;D
 I had heard someone makes a set for the magnum 500s, thought I might get lucky finding a set for the 66' styled wheel??  Thanks!
1967 Springtime Yellow Coupe, 289 2v 3spd, Metuchen built, Nov. 17th 66'
1966 Sahara Beige Coupe, 289 2v 3spd, Dearborn built, July 21st 66'
1964 1/2 Pagoda Green Coupe, 260 2v 3spd, Dearborn built, June 30th 64'
1966 GT350 Fastback clone, 289 HiPo, 725cfm Holley, 4spd, SanJose built, Nov 25th 65'

Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7099
Re: re-painting 66' styled wheels
« Reply #1 on: August 14, 2017, 12:04:06 PM »
I have no probelm hand taping them but could make better use of my time than spending a couple hours of masking. 
Take the time.
Jim
Let me expand. I made a "mask" for one section out of paper about 1/4 inch smaller and traced it on a sheet of paper with a black felt tip so I had five per sheet. Then I used my copier to make duplicates and cut them out with scissors. Steel wool the wheels to remove the old paint and mask away. That's one method.
Jim 
« Last Edit: August 14, 2017, 03:26:54 PM by jwc66k »
I promise to be politically correct in all my posts to keep the BBBB from vociferating.

Offline Hipo giddyup

  • Hero Member
  • *****
  • Posts: 1201
  • There is no end to doing right. Giddyup!!!
Re: re-painting 66' styled wheels
« Reply #2 on: August 14, 2017, 03:52:25 PM »
Yeah, I'm thinking that will be my only solution. Since these are the 66 wheels with the painted black rim, it sounds that dark charcoal is the correct color choice. One last question, is primer typically used ?? The originals don't appear to have any primer underneath.  So maybe use a self etching primer for good adhesion?
1967 Springtime Yellow Coupe, 289 2v 3spd, Metuchen built, Nov. 17th 66'
1966 Sahara Beige Coupe, 289 2v 3spd, Dearborn built, July 21st 66'
1964 1/2 Pagoda Green Coupe, 260 2v 3spd, Dearborn built, June 30th 64'
1966 GT350 Fastback clone, 289 HiPo, 725cfm Holley, 4spd, SanJose built, Nov 25th 65'

Offline midlife

  • Wiring Guru---let me check your shorts!
  • Global Moderator
  • Hero Member
  • ****
  • Posts: 2155
    • Midlife Harness Restorations
Re: re-painting 66' styled wheels
« Reply #3 on: August 14, 2017, 06:40:55 PM »
I taped up the chrome on mine, leaving rolled edges to create a soft paint line.  Then used VHT argent paint from a rattle can, after scuffing the untaped portions of the wheel.  Turned out very nice and only took a couple of hours, total. 
Midlife Harness Restorations - http://midlifeharness.com

Offline Hipo giddyup

  • Hero Member
  • *****
  • Posts: 1201
  • There is no end to doing right. Giddyup!!!
Re: re-painting 66' styled wheels
« Reply #4 on: August 14, 2017, 10:56:18 PM »
Never thought of rolling the edges, good tip. I was going to make a template cut out to mimic the soft edges and factory look but my luck it would get overspray where I wouldn't want it. I'm assuming Ford used a template for this application.
Thanks Midlife.
1967 Springtime Yellow Coupe, 289 2v 3spd, Metuchen built, Nov. 17th 66'
1966 Sahara Beige Coupe, 289 2v 3spd, Dearborn built, July 21st 66'
1964 1/2 Pagoda Green Coupe, 260 2v 3spd, Dearborn built, June 30th 64'
1966 GT350 Fastback clone, 289 HiPo, 725cfm Holley, 4spd, SanJose built, Nov 25th 65'