91
Drivetrain / Re: Guide to Original 1965 to 1973 Snubber Brackets
« Last post by Anghelrestorations on April 13, 2024, 06:35:46 PM »I feel old all of a sudden..... 
News:
Join us on Facebook: Search for 'ConcoursMustang' Private group!
Recent Posts
92
Wanted Ads / Re: WTBuy or Borrow Autolite Coil Stamp
« Last post by J_Speegle on April 13, 2024, 06:18:35 PM »PM sent
93
Drivetrain / Re: 9 Inch Axle Pinion Snubber
« Last post by J_Speegle on April 13, 2024, 06:13:53 PM »I found detailed information on 9 inch axle pinion snubbers done by Anghel Restorations.
https://anghelrestorations.com/wp-content/uploads/2021/09/pinion_snubber_v1.0.pdf
Yes nice work and thanks for the insight. Hard to believe that almost ten years has passed since it was posted. BTW the article is also posted in the Library section of this site with Marcus' permission
94
Parts for Sale / Re: 67 fb trap door and dash pad
« Last post by 68GT/CSconvmod on April 13, 2024, 04:29:24 PM »Consider offer or trade of nos 67-69 part.
95
1964 1/2 - 1965 / Re: 1694.5 Flasher location
« Last post by jwc66k on April 13, 2024, 02:37:27 PM »An assembly line flasher "should be" in a bracket attached to the left vent, or very close to it. If you have a copy pf the 1964 Mustang Electrical Manual (AM0003), pg 15, it's shown as item 4.
If you are a "large" driver (I'm 6 ft), consider removing the driver's seat and placing a packing blanket on the floor. It goes easier on the back that way.
Jim
If you are a "large" driver (I'm 6 ft), consider removing the driver's seat and placing a packing blanket on the floor. It goes easier on the back that way.
Jim
96
1964 1/2 - 1965 / 1694.5 Flasher location
« Last post by Corey Bowcutt on April 13, 2024, 11:57:16 AM »I have a 1964.5 Convertible project I am working on. I have gotten everything to work except the turn signals. I have checked all fuses and they are good. My next step was to check the flasher but I cannot for the life of me find it. Any suggestions on where to look? I have looked at the electrical assembly manual and electrical diagrams and that has been no help.
Thank you,
Corey
Thank you,
Corey
97
Drivetrain / Re: Push rod length
« Last post by RoyceP on April 13, 2024, 11:31:18 AM »Lots of them - it might help if we knew what diameter, the end design, and perhaps the application. Far too many options otherwise.
Here's a guide:
https://www.pushrods.net/custom-pushrod-selection
Here's a guide:
https://www.pushrods.net/custom-pushrod-selection
98
Wanted Ads / WTBuy or Borrow Autolite Coil Stamp
« Last post by dkknab on April 13, 2024, 11:01:56 AM »Looking for a stamp to buy or borrow.
99
1969 - 70 Shelby / Re: Space Saver Spare Tire Felt
« Last post by hopey on April 13, 2024, 08:09:10 AM »Anybody seen the yellow stripe on a shelby SS spare tire cover felt as i have seen 2 types of felts?
Similar question, I have also seen two types of felts. The thick grey one which is typically seen in Dearborn builds and a more brown colored felt which I have seen in at least a couple of 1970 BOSS 302 Metuchen builds. This is an example of the other felt. Has anyone else documented examples of this, was it a assembly plant difference or just a coincidence I saw it in Metuchen builds?
100
1969 - 70 Shelby / Re: Help with rim blow switch
« Last post by Tomdeg on April 13, 2024, 02:13:19 AM »I wised up and took it to Rimblow Restorations. I?ll let them put the new switch. Thanks for all the help.