Author Topic: Parking brake cable spring replacement  (Read 182 times)

Offline 67gta289

  • Hero Member
  • *****
  • Posts: 1388
Parking brake cable spring replacement
« on: February 16, 2017, 09:17:47 PM »
I have a great pair of parking brake cables, except that the return springs were cracked.  Strange that everything else was nice but that is the case.  I can't slip the springs over the end fitting.  Any repair suggestions?  I'm thinking I might be able to clear the fitting from a spare with a drill bit, cut the one off the new cable, then move the donor over and "crimp" it on with a press and die.   Thoughts and recommendations appreciated
John
67 289 GTA Dec 20 1966 San Jose
MCA 74660

Offline 1966KGT

  • Newbie
  • *
  • Posts: 47
Re: Parking brake cable spring replacement
« Reply #1 on: February 16, 2017, 11:10:26 PM »
without seeing the other end, if it is a ball, maybe you can cut ball off with dremel tool, remove cable, replace spring, slide cable back thru conduit, then "birdcage wire slightly", then clean wire with brake cleaner and make a mold with wood that you could melt lead into and pour into mold? crude but a possibility? in my line of work we re- end cables using this technique, but were using 1" cable, 40,000 #pull,  works well.

Offline 67gta289

  • Hero Member
  • *****
  • Posts: 1388
Re: Parking brake cable spring replacement
« Reply #2 on: February 17, 2017, 05:43:28 AM »
The other end is a ball - thanks for the idea, will look into that.
John
67 289 GTA Dec 20 1966 San Jose
MCA 74660

Offline Bob Gaines

  • Global Moderator
  • Hero Member
  • ****
  • Posts: 3885
Re: Parking brake cable spring replacement
« Reply #3 on: February 17, 2017, 01:05:42 PM »
without seeing the other end, if it is a ball, maybe you can cut ball off with dremel tool, remove cable, replace spring, slide cable back thru conduit, then "birdcage wire slightly", then clean wire with brake cleaner and make a mold with wood that you could melt lead into and pour into mold? crude but a possibility? in my line of work we re- end cables using this technique, but were using 1" cable, 40,000 #pull,  works well.
I would think at first thought lead being soft would not stand up under use on the thinner Mustang cable let alone a 1 inch cable with a possible 40,000 #pull but have never tried it on a Mustang cable let alone a 1" cable.  ;D I would have thought steel like original(Mustang)
« Last Edit: February 17, 2017, 02:25:09 PM by Bob Gaines »
Bob Gaines,Shelby enthusiast, Shelby collector , Shelby concours judge SAAC,MCA,Mid America Shelby

Offline mtinkham

  • Full Member
  • ***
  • Posts: 207
  • That'll be easy
Re: Parking brake cable spring replacement
« Reply #4 on: February 17, 2017, 02:02:17 PM »
Can you thread the spring onto the cable? Hold the middle of the spring 90 degrees to the cable and start "threading" or winding the spring around the cable, then work the other half of the spring?
1967 S-code Fastback, GT, 3-speed manual, Metuchen, Scheduled 04-21-1967 - Actual 04-25-1967

Offline 67gta289

  • Hero Member
  • *****
  • Posts: 1388
Re: Parking brake cable spring replacement
« Reply #5 on: February 17, 2017, 04:27:11 PM »
At first I thought you were saying to start a new thread  ;) will try that tonight and report back.
John
67 289 GTA Dec 20 1966 San Jose
MCA 74660