Author Topic: 67 vacuum tee  (Read 2734 times)

Offline 67350#1242

  • Sr. Member
  • ****
  • Posts: 305
Re: 67 vacuum tee
« Reply #15 on: March 06, 2017, 09:58:07 PM »
Marty, I found this diagram under brake section in the shop manual. This should verify trans hookup to check valve port. Every PB Auto 67 I've seen has it this way.
Kurt.
« Last Edit: March 06, 2017, 10:00:45 PM by 67350#1242 »
67 Coupe SJ 11/16/66
67 GT350 SJ 2/01/67

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24177
Re: 67 vacuum tee
« Reply #16 on: March 06, 2017, 10:15:53 PM »
Not to be argumentative but have a fair number of unrestored 67s with PB with the transmission vacuum connected to other sources. Not sure if it depends on time period, options or other key points
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline 67350#1242

  • Sr. Member
  • ****
  • Posts: 305
Re: 67 vacuum tee
« Reply #17 on: March 06, 2017, 10:29:19 PM »
No argument here Jeff, just relaying personal experience.  Here is a picture of 67 GT350 #165  Auto PB A/C  SJ 1/3/67 obviously unrestored.  All the vacuum lines are shown. (no tilt of course)
67 Coupe SJ 11/16/66
67 GT350 SJ 2/01/67

Offline jwc66k

  • Hero Member
  • *****
  • Posts: 7099
Re: 67 vacuum tee
« Reply #18 on: March 07, 2017, 12:37:37 AM »
There is a vacuum diagram in the 67 Mustang Chassis Assembly Manual, but be careful as the 390 page also applies to Cougars. A couple of "T's" are referenced using Ford design part number (not the hardware part number format) but they do not appear in the 75 Ford Car Parts book.
Jim
I promise to be politically correct in all my posts to keep the BBBB from vociferating.

Offline krelboyne

  • Hero Member
  • *****
  • Posts: 1190
    • West Coast Classic Cougars
Re: 67 vacuum tee
« Reply #19 on: March 07, 2017, 12:28:59 PM »
Marty, there is another vacuum "T" at the front of the intake manifold associated with the installation of the PCV transfer tube. See Mansfields site for an illustration.
Scott Behncke - Carcheaologist
West Coast Classic Cougars
503-463-1130
1968 GT/CS 302-4V San Jose 05B
1968 Cougar XR7 Dearborn 09A

Offline preaction

  • Hero Member
  • *****
  • Posts: 1323
Re: 67 vacuum tee
« Reply #20 on: March 12, 2017, 10:05:21 PM »
This car was posted as having a tilt column, on 67 390 cars the assembly manual calls for a tee in one of the vacuum lines after it leaves the brass distribution block, 6'' of tube, tee, then continuing on. On my engine this tee was black plastic  and in the AMK id book,  could this be it ?
8F02R218047-  July 18 1968   Dearborn

Offline Bob Gaines

  • Global Moderator
  • Hero Member
  • ****
  • Posts: 8956
Re: 67 vacuum tee
« Reply #21 on: March 12, 2017, 11:42:10 PM »
This car was posted as having a tilt column, on 67 390 cars the assembly manual calls for a tee in one of the vacuum lines after it leaves the brass distribution block, 6'' of tube, tee, then continuing on. On my engine this tee was black plastic  and in the AMK id book,  could this be it ?
I have seen translucent white plastic tees but not black ones. I confess I have not seen a lot of these for the tilt but given all of the other distributor ,windshield washer tees etc .are the translucent white ,a black tee would make me skeptical of it's origin. 
Bob Gaines,Shelby enthusiast, Shelby collector , Shelby concours judge SAAC,MCA,Mid America Shelby