Author Topic: 64 1/2 White lacquer  (Read 2593 times)

Offline Dave Stribling

  • Full Member
  • ***
  • Posts: 160
64 1/2 White lacquer
« on: December 13, 2010, 01:20:17 PM »
Working on a 64 1/2 PAce Car Coupe and ready to shoot the lacquer on the interior.  I know the 64 white interior color is different than 65, so I had the 8608 Ditzler number matched up to a new PPG number.  This white is very off white.  Was the original more of a creme color or was it bright white, or should it better match the door panels?  Haven't pulled them out yet to try to match.  In looking at pictures online it looks like a potpourrie of shades used on restored cars. Remember, this is the interior color not the pace car white.  Thanks!

Offline Pete Bush

  • Hero Member
  • *****
  • Posts: 650
Re: 64 1/2 White lacquer
« Reply #1 on: December 13, 2010, 02:05:14 PM »
Dave,

My Ditzler color charts info has the following codes:

#8321     Pace Car White (exterior)
#8608     64-1/2 White (interior)
#8612     65 & 66 White (interior)
#8678     64 -1/2, 65, & 66 Wimbledon White (exterior)

#8608 should be the correct color, are you saying that the #8608 you had mixed up doesn't look correct? Could it be that some of the photos of restored cars you're looking at have mistakenly used one of the other whites?
'66 6-cylinder Sprint Convertible
Metuchen - Scheduled May 10th; Built June 21st

Offline Dave Stribling

  • Full Member
  • ***
  • Posts: 160
Re: 64 1/2 White lacquer
« Reply #2 on: December 13, 2010, 05:42:07 PM »
Dave,

My Ditzler color charts info has the following codes:

#8321     Pace Car White (exterior)
#8608     64-1/2 White (interior)
#8612     65 & 66 White (interior)
#8678     64 -1/2, 65, & 66 Wimbledon White (exterior)

#8608 should be the correct color, are you saying that the #8608 you had mixed up doesn't look correct? Could it be that some of the photos of restored cars you're looking at have mistakenly used one of the other whites?

The Diztler mixes are long gone (PPG bought 'em).  In contact with PPG's Color hotline or whatever it was, they came up with a "This is durn' close" mix number of 90011.  Very creme colored but you tell me.  Was the 64 1/2 interior off white.  REAL Duracryl is getting uber expensive - if it ain't right I want to know before I shoot!


Offline Dave Stribling

  • Full Member
  • ***
  • Posts: 160
Re: 64 1/2 White lacquer
« Reply #3 on: December 13, 2010, 06:43:25 PM »
Just pulled the door panels out of the box, and the color matches pretty well.  Think I'll go with it.  Thanks!

Offline Pete Bush

  • Hero Member
  • *****
  • Posts: 650
Re: 64 1/2 White lacquer
« Reply #4 on: December 13, 2010, 06:52:24 PM »
You might want to check with these folks before you go too far:

http://www.tcpglobal.com/autocolorlibrary/

It's where I get my color code info.

Give 'em a call. Doesn't hurt to verify things.
'66 6-cylinder Sprint Convertible
Metuchen - Scheduled May 10th; Built June 21st

Offline bryancobb

  • Silver Level Subscriber
  • Hero Member
  • ****
  • Posts: 1077
  • 2009 Ridn' Around
Re: 64 1/2 White lacquer
« Reply #5 on: December 13, 2010, 07:21:40 PM »
Dave,
If you investigate a little deeper, I'll bet you can find some of the ORIGINAL paint on the back side of some of the interior pieces.  I found an almost spotless area of the underside of my quarter trim panels.  I had the local PPG jobber shoot that area with their X-Rite "Proffit" machine and mix my paint.  It looks perfect.  ( The color, not my spray job ) LOL
66 Metuch Conv
Nightmist, Std Blu Int
6T08C223904    76A       K         22       15c     21      6        6
                      BODY  COLOR   TRIM    DATE   DSO   AXLE  XMSN
   C/O  785                                   (rotation #)
   16    C14   6T08C223904        (weld bay 16, bucked MAR 14)

Offline Dave Stribling

  • Full Member
  • ***
  • Posts: 160
Re: 64 1/2 White lacquer
« Reply #6 on: December 14, 2010, 01:05:13 PM »
Dave,
If you investigate a little deeper, I'll bet you can find some of the ORIGINAL paint on the back side of some of the interior pieces.  I found an almost spotless area of the underside of my quarter trim panels.  I had the local PPG jobber shoot that area with their X-Rite "Proffit" machine and mix my paint.  It looks perfect.  ( The color, not my spray job ) LOL

Pulled the ashtray off the shelf and checked.  Dead on match.  Happy!