Author Topic: 67 convertible trunk divider clip  (Read 169 times)

Offline ruppstang

  • Hero Member
  • *****
  • Posts: 3834
67 convertible trunk divider clip
« on: April 22, 2024, 10:15:53 AM »
I am looking for the clip the retains the trunk divider at the top like in the picture. I cannot find it in the assembly manual. If someone knows where to find them or a part number that would be great.

Offline 67gta289

  • Hero Member
  • *****
  • Posts: 3024
Re: 67 convertible trunk divider clip
« Reply #1 on: April 22, 2024, 11:26:40 AM »
I looks to me like 358407 is the fastener number for the clip.

1. The interior assembly manual is of very poor quality, but I think I can see 358407-S2 - 3 required.
2. I did a search for that in all of the documents I have, and it only showed up in the 1958 Ford parts & accessories catalog, but associated with convertible folding top compartment trim.
3. Then I found it in Jim's spreadsheet to seal the deal.
John
67 289 GTA Dec 20 1966 San Jose
7R02C156xxx
MCA 74660

Offline CharlesTurner

  • Charles Turner
  • Administrator
  • Hero Member
  • *****
  • Posts: 7620
Re: 67 convertible trunk divider clip
« Reply #2 on: April 22, 2024, 11:37:38 AM »
Looks like ones used on a coupe?
Charles Turner - MCA/SAAC Judge
Concours Mustang Forum Admin

Offline 67gta289

  • Hero Member
  • *****
  • Posts: 3024
Re: 67 convertible trunk divider clip
« Reply #3 on: April 22, 2024, 01:49:58 PM »
Here are the specifications.  If you need some I can go shopping at the junkyard - let me know.
John
67 289 GTA Dec 20 1966 San Jose
7R02C156xxx
MCA 74660

Offline ruppstang

  • Hero Member
  • *****
  • Posts: 3834
Re: 67 convertible trunk divider clip
« Reply #4 on: April 22, 2024, 02:17:28 PM »
Yes, John that is it! Now to find some. It would be a pain to get off a junk car as it is under the top and well Linner.

Thanks again.

Offline 196667Bob

  • Hero Member
  • *****
  • Posts: 1042
Re: 67 convertible trunk divider clip
« Reply #5 on: April 22, 2024, 02:32:09 PM »
Marty : John "beat me" to the Part Number, but by a different method. Instead of the ASSEMBLY manual, I looked at the 1969 Standard and Utility Parts Book. Due to the uniqueness of the cLip, I figured it would be easy to spot. Sure enough, it shoed up (see attached). Note that there is a symbol shown before the part Number ; I couldn't find a legend for this symbol in the 1969 book, but I have a feeling that it might signify " Not Serviced - Factory Only". Then out of curiosity, I looked in the 1965 S&UP book ; it showed op there also (no symbol shown). Then I went back to my 1959 S&UP book (interestingly, the 1959 version also includes applications for most of the Hardware Part Numbers). The 358407 shoeed up in the 1959 with the application listed for the 1958 Convertible Top Storage Compartment. If the 358407 was "Not Serviced", this may help if you can't find a 67 that has these clips. Unfortunately, I won'y know if I have all of mine until I get to our Colorado place (where you may remember my 67 is) until June or July.

Hope this helps.

Bob

1966 Coupe, C Code, 3 Sp MT, 6T07C154XXX, Build Date 11/22/65
1967 Conv, C Code, C4, 7F03C154XXX, Actual Build Date 01/31/67
MCA 04909

Offline 67gta289

  • Hero Member
  • *****
  • Posts: 3024
Re: 67 convertible trunk divider clip
« Reply #6 on: April 22, 2024, 08:29:33 PM »
Yes, John that is it! Now to find some. It would be a pain to get off a junk car as it is under the top and well Linner.

Thanks again.

Most of the convertibles in this particular yard have had the tops removed, and I have power tools lol.  If you strike out elsewhere let me know.
John
67 289 GTA Dec 20 1966 San Jose
7R02C156xxx
MCA 74660

Offline ruppstang

  • Hero Member
  • *****
  • Posts: 3834
Re: 67 convertible trunk divider clip
« Reply #7 on: April 22, 2024, 08:51:10 PM »
Wow it is hard to believe that there are convertibles still in a junk yard. That must be a good one.

Offline 67gta289

  • Hero Member
  • *****
  • Posts: 3024
Re: 67 convertible trunk divider clip
« Reply #8 on: April 22, 2024, 08:54:42 PM »
There's a 65 K-code, red with black interior, 4-speed with locking axle.  Of course just about everything is gone.  Might have clips!

A few year ago I pulled out a 68 Cougar R-code.  There are five 1969 Mach 1's.  GTO, Cyclone, 442, Charger... It is like walking back in time.
John
67 289 GTA Dec 20 1966 San Jose
7R02C156xxx
MCA 74660

Offline ruppstang

  • Hero Member
  • *****
  • Posts: 3834
Re: 67 convertible trunk divider clip
« Reply #9 on: April 22, 2024, 08:56:25 PM »
Marty : John "beat me" to the Part Number, but by a different method. Instead of the ASSEMBLY manual, I looked at the 1969 Standard and Utility Parts Book. Due to the uniqueness of the cLip, I figured it would be easy to spot. Sure enough, it shoed up (see attached). Note that there is a symbol shown before the part Number ; I couldn't find a legend for this symbol in the 1969 book, but I have a feeling that it might signify " Not Serviced - Factory Only". Then out of curiosity, I looked in the 1965 S&UP book ; it showed op there also (no symbol shown). Then I went back to my 1959 S&UP book (interestingly, the 1959 version also includes applications for most of the Hardware Part Numbers). The 358407 shoeed up in the 1959 with the application listed for the 1958 Convertible Top Storage Compartment. If the 358407 was "Not Serviced", this may help if you can't find a 67 that has these clips. Unfortunately, I won'y know if I have all of mine until I get to our Colorado place (where you may remember my 67 is) until June or July.

Hope this helps.

Bob

Thanks for the detective work. How is your car coming along?

Offline ruppstang

  • Hero Member
  • *****
  • Posts: 3834
Re: 67 convertible trunk divider clip
« Reply #10 on: April 22, 2024, 08:58:24 PM »
There's a 65 K-code, red with black interior, 4-speed with locking axle.  Of course just about everything is gone.  Might have clips!

A few year ago I pulled out a 68 Cougar R-code.  There are five 1969 Mach 1's.  GTO, Cyclone, 442, Charger... It is like walking back in time.

Wow those would be some great cars, especially  the K convertible.

Offline 67gta289

  • Hero Member
  • *****
  • Posts: 3024
Re: 67 convertible trunk divider clip
« Reply #11 on: April 22, 2024, 09:02:37 PM »
Wow those would be some great cars, especially  the K convertible.

Looks like a long weekend project.
John
67 289 GTA Dec 20 1966 San Jose
7R02C156xxx
MCA 74660