« previous next »
Pages: [1]   Go Down

Author Topic: Rubber Shield Fasteners  (Read 2179 times)

Offline imnutz66

  • Newbie
  • *
  • Posts: 18
Rubber Shield Fasteners
« on: April 07, 2010, 07:54:32 AM »
Can someone tell me what fastener was used to install the rubber flap above the rear license plate on 70's? I have the holes there, but the flap was removed by PO along with the fasteners

Thanks, Joe
Logged
70 Mach 1 351C 4V 4Speed
Dearborn
Born October, 1969

Offline Bill73Ragtop

  • Newbie
  • *
  • Posts: 7
Re: Rubber Shield Fasteners
« Reply #1 on: April 07, 2010, 09:33:56 AM »
My 69 vert had philips head screws.  It was original as far as I could tell.  I replaced them with stainless screws when re-assembling.
Logged

Offline cobrajetchris

  • Sr. Member
  • ****
  • Posts: 335
Re: Rubber Shield Fasteners
« Reply #2 on: April 07, 2010, 11:44:07 AM »
The ones I have seen are all round head Phillips screws that are very short and have a black phosphate type coating, I am sure AMK fasteners would have them.
Logged
CHRIS KNOBBE
69 MUSTANG COUPE, DEARBORN BUILT 06/10/69 OWNED SINCE 1978
70 BOSS 302 MUSTANG, DEARBORN BUILT 10/24/69 OWNED SINCE 1987
69 R CODE MACH1 AUTO, DEARBORN BUILT 10/10/68 OWNED SINCE 2006
69 R CODE MACH1 4 SPEED (factory black) SAN JOSE BUILT 12/30/68 OWNED SINCE 2007

Offline imnutz66

  • Newbie
  • *
  • Posts: 18
Re: Rubber Shield Fasteners
« Reply #3 on: April 07, 2010, 12:23:59 PM »
Thanks for the info, were they round head for sure and not pan head?
Logged
70 Mach 1 351C 4V 4Speed
Dearborn
Born October, 1969

Offline J_Speegle

  • Administrator
  • Hero Member
  • *****
  • Posts: 24218
Re: Rubber Shield Fasteners
« Reply #4 on: April 07, 2010, 09:08:43 PM »
Only seen round head phillips used
Logged
Jeff Speegle

Anything worth doing is worth doing concours ;)

Offline rockhouse66

  • Hero Member
  • *****
  • Posts: 929
Re: Rubber Shield Fasteners
« Reply #5 on: April 08, 2010, 10:57:21 AM »
This is from a 1969 Dearborn car.  I am sure the original finish was P&O.

Logged
Jim
'66 GT FB

Offline imnutz66

  • Newbie
  • *
  • Posts: 18
Re: Rubber Shield Fasteners
« Reply #6 on: April 08, 2010, 11:23:42 AM »
That picture is great, I actually have a handful of screws identical to that - if I can just remember exactly where they are!
Logged
70 Mach 1 351C 4V 4Speed
Dearborn
Born October, 1969

Offline Bob Gaines

  • Global Moderator
  • Hero Member
  • ****
  • Posts: 8984
Re: Rubber Shield Fasteners
« Reply #7 on: April 08, 2010, 11:34:50 PM »
Those screws look like the screws  at the bottom that hold the interior dash trim pieces of the two in the center (ether side of radio)and two outer trim panels on a 69. AMK sells them. Bob
Logged
Bob Gaines,Shelby enthusiast, Shelby collector , Shelby concours judge SAAC,MCA,Mid America Shelby
Pages: [1]   Go Up
« previous next »