Recent Posts

1

General Discussion / Re: Well liner

« Last post by Bob Gaines on Today at 01:41:27 PM »

I am looking for a well liner for my 1970 convertible. I can't find a one piece with pockets for weight rods. And backer board would be nice. Does anyone know who makes them? Thanks Jay.

Dead nuts On used to but has had a problem finding the special flexible water resistant cardboard that the factory used. You should call him for a update. Otherwise before Dead nuts on exact reproduction you would take a used well liner with sewed on board pattern to a upholstery shop and have them make one up from scratch. I would take the board which I worked over to look as close as possible and had the upholstery shop make up the liner and sew it to the board.

2

General Discussion / Well liner

« Last post by born2race59 on Today at 01:11:51 PM »

I am looking for a well liner for my 1970 convertible. I can't find a one piece with pockets for weight rods. And backer board would be nice. Does anyone know who makes them? Thanks Jay.

3

Wanted Ads / Re: C8ZX-9510-A

« Last post by Coralsnake on Today at 10:12:11 AM »

I have a throttle body, but its missing quite a few parts. I know the metering blocks are gone and probably the bowls?

4

Wanted Ads / C8ZX-9510-A

« Last post by Gahendo on Today at 01:39:59 AM »

My 500 has a service replacement. Im looking for a C8ZX-9510-A to put on it.
Would like a complete carb that can be rebuilt or already rebuilt.

Thanks

5

1969 Mustang / San Jose Door hinge sealer?

« Last post by jmlay on April 15, 2024, 11:37:03 PM »

Is there a difference in application of sealer around the door hinges between plants? I found the post below, indicating a small continuous bead of sealer on the front and top of the upper hinge, Dearborn. Is this the same for San Jose? Thoughts on the lower hinge?

https://www.concoursmustang.com/forum/index.php?topic=20565.msg129672#msg129672

Thanks
Mike

6

1969 Mustang / Re: Heater Hose clamp or bracket

« Last post by J_Speegle on April 15, 2024, 11:07:14 PM »

I have a 1969 with a 302 engine. The car did not come with A/C. There are two heater hoses which need to be properly clamped down/attached. At the moment they are not attached to anything in the engine compartment and basically are sitting on the valve covers. ..............

The two hoses pass through the firewall and attach to the non-AC heater box/heater core at the nipples. No bracket to hold them and clamps only in the interior - not visible from engine compartment on a non AC car




Different year but same design and route



The other ends attach to the nipple on top of the intake (front) and the other to the second water pump nipple at the front of the engine






There is a whole handful of pictures of the engine compartments in the Unrestored 69 Mustang section. In some cases (common after all these years) the hoses and clamps have been replaced but will at least, in those examples, show you where they attach. Any of the non AC small blocks should help

If your going for the original look you'll need tower clamps at both ends. Ford part numbers will do you little good but undated reproductions are available

7

Processes, Products & Techniques / Re: Weatherstrip Adhesive Removal

« Last post by RoyceP on April 15, 2024, 11:03:39 PM »

I've had good luck with charcoal lighter fluid and it doesn't hurt the paint.
[/quote




Well he is talking about the seal so no paint is involved.

8

Misc Items / MOVED: ? Cowl to Hood seal Brackets

« Last post by J_Speegle on April 15, 2024, 10:40:54 PM »

This topic has been moved to 64 1/2 - 65 Mustang & Shelby.

https://www.concoursmustang.com/forum/index.php?topic=363.0

9

1969 Mustang / Re: Heater Hose clamp or bracket

« Last post by Bob Gaines on April 15, 2024, 10:04:41 PM »

I will get the manual but I am wondering what those holes on the firewall are for?

One could be for the engine block (back of the head) to firewall ground. Also you have larger holes for the rubber plugs holding the firewall pad on.  That is in the electrical manual . https://www.npdlink.com/product/assembly-manual-1969-complete/217284 . It is all covered in the manuals.

10

1969 Mustang / Re: Heater Hose clamp or bracket

« Last post by lmennis on April 15, 2024, 10:01:16 PM »

I will get the manual but I am wondering what those holes on the firewall are for?