Author Topic: Cobra Jet Detailing Guide  (Read 264 times)

Offline azscj

  • Hero Member
  • *****
  • Posts: 691
    • Anghel Restorations
Cobra Jet Detailing Guide
« on: January 12, 2018, 05:49:52 PM »

I put together a new guide on how to detail a typical Cobra Jet engine especially with the 50th anniversary happening this year of the official release.  This is an update of information plus adding some more new information we have not had.  The goal here was to review some of the most common items and not go into the internals of the motor.

Welcome to comments, questions or suggestions here. 

Its a long article so give it a minute to load on your screen.

http://anghelrestorations.com/uploads/3/5/1/2/35122002/cobrajet_engine_detail_v1.0c.pdf

IMG_5996 Fixed-002 by Marcus Anghel, on Flickr



Marcus Anghel
MCA National Gold Card Judge, 69-71 Mustang
SAAC National Head Judge, Boss Mustangs

http://www.anghelrestorations.com/
https://www.facebook.com/anghelrestorations

Offline JohnRB

  • Full Member
  • ***
  • Posts: 132
Re: Cobra Jet Detailing Guide
« Reply #1 on: January 12, 2018, 06:36:13 PM »
Perfect.

A few comments.

In topic #2 : Its missing a J in Cobra Jet.

Under topic # 5. Just a question regarding exhaust manifolds. Did early 70 exhaust manifolds have provision for the choke stove? If not, are they different than 69?

Topic #18. Are distributor brackets the same all years/California emission?

Marcus. You realy have to write a book!

Thanks for what you do and share with us.

John in Norway

Offline Coralsnake

  • Full Member
  • ***
  • Posts: 174
Re: Cobra Jet Detailing Guide
« Reply #2 on: January 12, 2018, 06:49:43 PM »
The original C8 motor mount insulators I have seen have a red ID stripe. Im not sure how long they continued use of them......

1968 Shelbys have a few other variants as well.

Thanks for sharing this information

Offline Bob Gaines

  • Global Moderator
  • Hero Member
  • ****
  • Posts: 4395
Re: Cobra Jet Detailing Guide
« Reply #3 on: January 12, 2018, 06:54:58 PM »
Great in depth article . The best yet IMO.  I saw a typo in #8 Engine tag was commonly placed under "coil bracket " bolt . You had dist hold down. #14 FYI the silver color on the valve cover gasket was a sealer . #32 the more common trademark on the bell shaped sender for 69 was FOMOCO in block letters in the rectangle. The Ford script version was less common IMO. 
Bob Gaines,Shelby enthusiast, Shelby collector , Shelby concours judge SAAC,MCA,Mid America Shelby

Offline Mike_B_SVT

  • Full Member
  • ***
  • Posts: 226
Re: Cobra Jet Detailing Guide
« Reply #4 on: January 14, 2018, 03:45:58 AM »
I posted this over on the CJ forum, but thought I should include it here as well...

Awesome document, Marcus and Bob!

Noted a few typos, missing(?) info, and possibly some corrections to be made?  Not criticizing, just trying to help - and gain a better understanding of these details.

Pg 6, #18 - "Distributor bracket" - I believe this should be Ignition Coil Bracket.

Pg 7, #21 - the picture on the right shows a D0ZF-AB carb, but the text beneath the picture describes the 1968 carb in the other pic.  I think the '68 carb image may also have lost some of its text.

Pg 8, #22 - I have my original D0 motor mounts, if you want any pics.

Pg 8, #23 - no mention of the different versions of CJ oil pan (C8 and C9) and how they can be identified externally by the baffle spot welds?  Also no mention of the windage tray and its variations?

Pg 9, #27 - Alternator fan blade change dates don't appear to match between the text on the images and in the description text.

Pg 10, #30 - wasn't there also a 1970 spacer version that had 4 holes, instead of the double "kidney bean" shapes?

Pg 11, #34c - Aren't BOTH brackets in the picture used for the alternator?  The smog pump adjusting bracket is not pictured, but it is mentioned in the text.
Pg 11, #34e - text seems confusing to me... "...except those with AC that had an additional bracket as shown here above."  I get the gist of the washer spacer, but what is this additional bracket that's mentioned?

Pg 13, #38 - this describes the 1969 starter cable mounting.  Do you plan to add the 1970 starter cable mounting info?

That's as far as I've gotten ~ time for bed.  Can't wait to finish reading the rest of it though!  Wow!
Mike B.

2003 Mustang Cobra Convertible
1 of 354 in Sonic Blue

1970 Cougar Eliminator (Competition Gold / Black Decor Interior), 428SCJ, Ram-Air, 4-speed w/ Hurst shifter
Built: Dearborn, Oct 6th, 1969
Cat Bites Man!

Offline azscj

  • Hero Member
  • *****
  • Posts: 691
    • Anghel Restorations
Re: Cobra Jet Detailing Guide
« Reply #5 on: January 14, 2018, 11:16:07 AM »
Thanks for the inputs everyone.....I needed another set of eyes on this.  Will post an updated version in the next few days and update the thread when its done. 
Marcus Anghel
MCA National Gold Card Judge, 69-71 Mustang
SAAC National Head Judge, Boss Mustangs

http://www.anghelrestorations.com/
https://www.facebook.com/anghelrestorations

Offline Mike_B_SVT

  • Full Member
  • ***
  • Posts: 226
Re: Cobra Jet Detailing Guide
« Reply #6 on: January 14, 2018, 02:27:29 PM »
Finishing reading, here are a few other things that caught my eye...

Pg 15, #45e - "The oil cooler bracket was held in place with two special brackets..." 

Pg 15, #47 - just me being a picky editor, but I think the image with the fuel pump date code should have the text portion in the same order as the stamped number, for a more direct correlation.  "9M8A" stamp / "1969 Dec 8 First Shift" text.

Pg 16, #50 - the C9ZE-E fans have no date code?  Mine has a "27" and "u" (greek Mu) stamped in one fin.  Is this some sort of inspection stamp and not a date code?  Or is mine stamped because it was a service replacement?


Ok, that's all I got :-)  Thanks for the excellent article!

Mike B.

2003 Mustang Cobra Convertible
1 of 354 in Sonic Blue

1970 Cougar Eliminator (Competition Gold / Black Decor Interior), 428SCJ, Ram-Air, 4-speed w/ Hurst shifter
Built: Dearborn, Oct 6th, 1969
Cat Bites Man!

Offline 1969 Cale II

  • Full Member
  • ***
  • Posts: 165
Re: Cobra Jet Detailing Guide
« Reply #7 on: January 14, 2018, 10:56:40 PM »
Great story. It is amazing how many experts won't share what they know. This site has plenty of knowledge to share, and willing to. I am glad I am part of it. Everybody keep up the GREAT work.
Chris

Offline 69428SCJ

  • Newbie
  • *
  • Posts: 23
Re: Cobra Jet Detailing Guide
« Reply #8 on: January 15, 2018, 01:18:41 AM »
This is a fantastic document! It's going to help me quite a bit, I do have some suggestions though, mostly grammar. Under number 11, it should read, "There were two basic versions..." same applies to changing was to were in the first sentence in numbers 27, 37, 45a, and 50. Also, could a section be added indicating how much of the engine was assembled that received paint and/or parts that are clearly painted along with those that aren't plainly obviously painted?

Offline ramblewood390GT

  • Newbie
  • *
  • Posts: 11
Re: Cobra Jet Detailing Guide
« Reply #9 on: January 15, 2018, 05:27:33 PM »
Great work, very helpful and well-written.
New guy needs help with: 6/20/68 San Jose 390GT
8R01S165XXX 65A M 2D 10F 53 G 5