ConcoursMustang Forums

1st Generation 1964 1/2 - 1973 - Questions & general discussions that apply to a specific year => 1967 Mustang => Topic started by: Z67Fback on October 19, 2020, 09:43:01 PM

Title: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: Z67Fback on October 19, 2020, 09:43:01 PM

Can anyone explain where the  2 flat washers(one per side) go on the 1967 front bumper brackets. The assembly picture below is unclear and an online video says the flat washer goes under the lower bracket- this seems odd. Thank you!

Title: Re: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: Bossbill on October 19, 2020, 10:22:43 PM

I gather you don't have an Assembly Manual?

Here is what the Assy Manual says:

Title: Re: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: ruppstang on October 19, 2020, 10:29:12 PM

It uses flat washers because the rear holes are ovals for adjustment.

Title: Re: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: J_Speegle on October 20, 2020, 12:38:07 AM

Bossbill - What is the date on that page you posted? 


In any case here is an example of the hardware from a 67 NJ car (7T1558xx) for confirmation

(http://www.concoursmustang.com/forum/gallery/14/6-191020233516.jpeg)


While looking checked Dearborn and San Jose and there appears to be possible differences between the practices at different plants but will keep that for a different thread

Title: Re: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: Bob Gaines on October 20, 2020, 12:41:41 AM

Flat washer,lock washer then the bolt is what I have seen . It is also what Jeff's picture shows.   

Title: Re: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: Bossbill on October 20, 2020, 01:16:42 PM

Quote from: J_Speegle on October 20, 2020, 12:38:07 AM

Bossbill - What is the date on that page you posted? 
SNIP

Jeff -- 2009 on the back cover of the Osborne. That particular page has no date.

Title: Re: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: J_Speegle on October 21, 2020, 05:25:00 PM

Quote from: Bossbill on October 20, 2020, 01:16:42 PM

Jeff -- 2009 on the back cover of the Osborne. That particular page has no date.

Odd that there is not a revision or creation date but thanks for looking

Title: Re: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: Bossbill on October 21, 2020, 06:35:46 PM

I should have been a bit less gruff in my answer to Z67Fback since the Assy Manuals are always 'this is what we want you to do', not necessarily what was done at any or all plants.
As well, the pages that Osborn has collect can vary by implementation/revision date as he chooses the versions that can be found or read.

There are now additional threads on this topic, including one of my own car -- without the flat washer!

Title: Re: NJ 1967 Mustang Front Bumper bracket mounting hardware
Post by: Z67Fback on October 21, 2020, 09:18:48 PM

Thanks all for the collective knowledge.  All input is appreciated. Sometime it is a puzzle sorting out assembly manual drawings, shop manuals, plant variations, bad info on internet and cars that have been modified in creative ways of the past 50 years.

Take Care,
Scott