Recent Posts

1

1968 Mustang / 1968 Mustang woodgrain inserts

« Last post by nightmist on Today at 07:53:05 AM »

I am restoring a 1968 Mustang fastback GT with decor interior.  What is the best option for the woodgrain door, dash and upper console inserts? 

I have read a lot of complaints online about the aftermarket woodgrain kits not fitting well--shrinking, peeling, bubbling in heat--and the patterns not matching across the various panels.  Is there a more expensive option that looks better and lasts?

2

1970 Mustang / MACH 1 Stripes

« Last post by NPRK on Today at 06:27:33 AM »

HI GUY's ,
Are the Mach 1 stripes painted on or are they stickers?

Cheers Keith

3

Processes, Products & Techniques / Re: Red Dyed Hardware

« Last post by bullitt68 on Today at 12:55:24 AM »

I don't see any reason to reinvent the wheel. Of course it is always good to have a alternative if needed.The Dykem layout dye that I got 1 month ago is transparent and looks the same as always. Besides being the product that AMK used and most likely still uses I am not for sure if the ink would hold up as good as the layout dye. Maybe it does but no good reason for me to change IMO.  Plus it is easily accessible if I run out from Amazon or my local welding supply.

Agreed Bob. I was messing with dye and paint and other products, but ordered the Dykems dye and there is no going back now. It's cheap and far more durable from what I can tell as it is designed to be used on metal. The other methods are good in a pinch, but for the cost my money is on the machinist dye. However it does not work very well on phosphate, but appears that AMK uses a thicker non translucent product on the phosphate fasteners. The master cylinder, steering box bolts, idler arm nuts and bolts as well as the pitman arm nut for example. They appear to be painted. Not sure what they use but it does appear to be non translucent. When I tried the machinist dye on phosphated parts it was very hard to see the dye. I used the Dykems dye on the rear leaf spin/ axel nuts, as well as third member nuts

4

1964 1/2 - 1965 / Re: Hole in firewall - what belongs there?

« Last post by CharlesTurner on Today at 12:28:57 AM »

Maybe the assembly line worker drilled the wrong hole for the choke cable?  An A/C line hole would have been bigger.

5

1964 1/2 - 1965 / Re: Hole in firewall - what belongs there?

« Last post by Bob Gaines on April 26, 2024, 11:42:47 PM »

It looks like the impression left from a hole saw with the drill bit hole in the center.

6

1964 1/2 - 1965 / Hole in firewall - what belongs there?

« Last post by cobrapatrol on April 26, 2024, 11:24:27 PM »

My Nov 64 SJ K-code fastback has a hole in the firewall approximately where the A/C hoses would go - pictured below. But, of course, this car never had A/C and the hole is round, not oval like the A/C opening would be.  I am curious to know what the purpose of this hole would might have.  There is a slight imprint next to the hole, and a second smaller hole at a slight angle, that may have been from something that was later removed.  The firewall insulation is pierced there also.

Any info is appreciated - Jim

7

Processes, Products & Techniques / Re: Red Dyed Hardware

« Last post by Bob Gaines on April 26, 2024, 10:36:51 PM »

Per Bossbill?s suggestion, I tried some Pinata Sante Fe red ink.  Here?s a photo of how it compares in color to red nut  from an NOS strut kit.   Appears pretty close.   The nut on the right is an original that was bead blasted then colored with the Pinata ink.  Nuts on the left are from the strut kit.  Fwiw

I don't see any reason to reinvent the wheel. Of course it is always good to have a alternative if needed.The Dykem layout dye that I got 1 month ago is transparent and looks the same as always. Besides being the product that AMK used and most likely still uses I am not for sure if the ink would hold up as good as the layout dye. Maybe it does but no good reason for me to change IMO.  Plus it is easily accessible if I run out from Amazon or my local welding supply.

8

Processes, Products & Techniques / Re: Red Dyed Hardware

« Last post by AJ on April 26, 2024, 08:12:48 PM »

Per Bossbill?s suggestion, I tried some Pinata Sante Fe red ink.  Here?s a photo of how it compares in color to red nut  from an NOS strut kit.   Appears pretty close.   The nut on the right is an original that was bead blasted then colored with the Pinata ink.  Nuts on the left are from the strut kit.  Fwiw

9

1967 Mustang / Re: 1967 Front Bumper Overstamped Factory Codes

« Last post by ruppstang on April 26, 2024, 02:58:59 PM »

A picture would be great.

10

Body, Paint & Sealers / MOVED: Mach one hood stripes

« Last post by J_Speegle on April 26, 2024, 02:05:04 PM »

This topic has been moved to 1969 Mustang.

https://www.concoursmustang.com/forum/index.php?topic=29630.0