ConcoursMustang Forums

1st Generation 1964 1/2 - 1973 - Questions & general discussions that apply to a specific year => 1964 1/2 - 1965 => Topic started by: JohnZee on November 30, 2010, 10:22:33 PM

Title: Correct Fender Bolts for 64 1/2 Dearborn
Post by: JohnZee on November 30, 2010, 10:22:33 PM

I have a 64 1/2 Mustang coupe built on July 17 / 64 in Dearborn.  I'm looking for the correct fender bolts.  The car is pretty original and I currently have black bolts with black lock washers. 

However, in all the shows that I've been to, I'm the only car with black bolts with lock washers. Is this correct  Most other 65's at stainless steel with flat silver washers.  I have purchased a set of these bolts (aftermarket), but want to make sure I'm not going away from the original.

Any ideas or comments ?   

Title: Re: Correct Fender Bolts for 64 1/2 Dearborn
Post by: CharlesTurner on November 30, 2010, 11:36:39 PM

Both styles are correct with varying head markings.  Do yours with the disc washers have something like a wavy flag logo?

The original finish would have been phosphate/oil.  There's lots of info on that here on this forum and some DIY instructions.

If you don't want to bother with re-finishing, AMK products sells some pretty nice reproductions.  www.amkproducts.com

Title: Re: Correct Fender Bolts for 64 1/2 Dearborn
Post by: 5F09CNot4Sale on December 01, 2010, 01:11:47 AM

I have a late June car however it is not where I can look at it ATM. I can say 100% from memory they bolts are all original and they do vary.

+1 caspian65

Title: Re: Correct Fender Bolts for 64 1/2 Dearborn
Post by: rockhouse66 on December 01, 2010, 08:57:44 AM

Just to clarify, the stainless steel bolts with silver flat washers you have seen on other cars are definitely incorrect.  The issue others are referencing is whether they should have star or round washers under the heads and which head marking.  They will be gray/black color phosphate and oil finish no matter which style.

Title: Re: Correct Fender Bolts for 64 1/2 Dearborn
Post by: 5F09CNot4Sale on December 01, 2010, 11:24:59 AM

Thanks rockhouse66, I should have been more clear. What I get for posting on sinus meds.

What rockhouse66 said is what I ment to say.

Title: Re: Correct Fender Bolts for 64 1/2 Dearborn
Post by: J_Speegle on December 01, 2010, 07:41:34 PM

Here is a picture (well clearest) of a car close to your projected build date - same plant. Hope it narrows down the possibilities a bit. No big head markings of the fender bolts on this car or a couple of others around that time

(http://i44.photobucket.com/albums/f49/firetrainer/64%20Details/LateJuneDearbornfenderbolt.jpg)

Title: Re: Correct Fender Bolts for 64 1/2 Dearborn
Post by: JohnZee on December 04, 2010, 08:11:04 PM

Thanks Everyone,

Jeff - my bolts look like the one in your photo - only  mine are completely gloss black rather than the nice rust colour pictured :-)   

The bolt threads were left untouched, so over time a small rust stain crept up around each bolt head.  In the past, I removed each bolt, treated with WD-40.  This seems to have stopped this problem. 

So what I hearing is that I should stick with my original bolts, they should be blasted clean,  and then gray/black color phosphate and oil finish added (including the threads) - can someone  confirm ?

Thanks again everyone !   

Title: Re: Correct Fender Bolts for 64 1/2 Dearborn
Post by: rockhouse66 on December 04, 2010, 09:44:33 PM

Quote from: JohnZee on December 04, 2010, 08:11:04 PM

So what I hearing is that I should stick with my original bolts, they should be blasted clean,  and then gray/black color phosphate and oil finish added (including the threads) - can someone  confirm ?

That's what I would do (and did on my own car).

Title: Re: Correct Fender Bolts for 64 1/2 Dearborn
Post by: 5F09CNot4Sale on December 04, 2010, 10:16:30 PM

That is what I am also doing to my June and Sept 64 cars.