Recent Posts

1

Parts for Sale / 69' Door panel cups

« Last post by Azdriver on Today at 11:32:06 AM »

Pair of original long style door panel pull cups. No cracks.  $120 shipping included in cont US

New pair of Scott Drake door panel cups. $60 shipping included in cont US.

Pat

2

Parts for Sale / Smog check valves

« Last post by Azdriver on Today at 11:19:26 AM »

Pair of reproduction smog check valves. Purchased from SEMO mustang never used. $195 shipping included in cont US.

Pat

3

Interior & Trunk / Mustang 67 red upholstery (deluxe)

« Last post by JoshG on Today at 10:25:19 AM »

Hi all,
my name is Joerg and I am from Germany.
I recently bought TMI deluxe upholstery and now recognized that the piping color differs.
The piping on the upholstery that was I installed looks like it?s all painted in the same color also the slight metallic effect is visible on the piping.
I wanted to ask is anyone can tell if the TMI upholstery comes with non-painted pipings or did I get a defect product.
Besides that I consider the appearance as imperfect, I fear the non-painted pipings might bleach from sunlight especially on my convertible.
TMI didn?t answer my question which is quite disappointing.

2 photos attached: former upholstery vs. TMI new ones
Thanks a lot in advance
Joerg

4

Body, Paint & Sealers / Still looking for correct textured hood stripe paint for ?70 Mach 1

« Last post by DaveF on May 03, 2024, 11:55:15 PM »

I am getting ready to have my hood repainted. I have the stencil for it, but I am having trouble finding the correct, textured matte black paint to do the hood stripes. Thanks

5

Body, Paint & Sealers / What is the correct paint for Mach 1 rocker moundings?

« Last post by DaveF on May 03, 2024, 11:42:51 PM »

Recently, I bought some paint from NPD. It is a very dark charcoal grey that is almost black. The color of my rocker molding is a much lighter gray. Could someone give me an indication of which one is right, or where I might find the right shade of grey?

6

Drivetrain / Re: s code low compression

« Last post by lightwtjet on May 03, 2024, 08:58:07 PM »

As Jeff may have eluded, an engine sitting for years can develop stuck rings. Simply driving fixed mine.
Here is more of what can be learned from a leak down test.
https://www.mobil.com/en/lubricants/for-personal-vehicles/auto-care/vehicle-maintenance/h

7

Parts for Sale / Re: 1965/66 Heater Plenum

« Last post by outlawincorporated on May 03, 2024, 06:19:20 PM »

from memory this heater plenum was used for falcon applications not mustangs.

regards

PHILL BERESFORD
MELBOURNE.
AUSTRALIA.

8

1964 1/2 - 1965 / Re: Holes in dash

« Last post by J_Speegle on May 03, 2024, 06:08:00 PM »

Thanks guys! I'm going to start welding up some holes.

Hammer them flat since they often are irregular from tightening the screw or drill bit into the hole when made

Get a cooper plate to hold on the back side and it should go well

9

Wanted Ads / Holley Metering blocks

« Last post by 68GT/CSconvmod on May 03, 2024, 01:50:49 PM »

4516 , 3434, 3563 

10

Parts for Sale / Re: 1965/66 Heater Plenum

« Last post by CW4macret on May 03, 2024, 01:44:27 PM »

This is the plenum I had installed for years. Never lost a point because it meets the requirement on the Concours judging sheet. Agree it is not exactly the same as what you normally see but it is a OEM 65/66 ford plenum. Dealer replaced???