91
General Discussion / Re: AACA Sr. Grand National 1968 Metuchen Coupe
« Last post by Bob Gaines on May 06, 2024, 01:22:17 PM »Congratulations.
News:
Join us on Facebook: Search for 'ConcoursMustang' Private group!
Recent Posts
92
Drivetrain / Re: Autolite 4300 Carburetor C9ZF-F
« Last post by Bob Gaines on May 06, 2024, 01:20:59 PM »I must have got lucky, sent mine to Tim Lancaster at Classic Carb Restorations in North Carolina for a rebuild and it came out of the box running great, no issues with it.There is always that one guy.
93
Drivetrain / Re: Autolite 4300 Carburetor C9ZF-F
« Last post by Coralsnake on May 06, 2024, 12:28:42 PM »I must have got lucky, sent mine to Tim Lancaster at Classic Carb Restorations in North Carolina for a rebuild and it came out of the box running great, no issues with it.
94
Drivetrain / Re: Autolite 4300 Carburetor C9ZF-F
« Last post by CharlesTurner on May 06, 2024, 12:26:26 PM »After working dozens of hours on a C8ZF-D 4300, finally threw in the towel and installed a Holley, engine runs perfect. Couldn't get a smooth idle with the 4300 no matter what I did.
95
General Discussion / Re: AACA Sr. Grand National 1968 Metuchen Coupe
« Last post by DTruitt on May 06, 2024, 11:55:49 AM »Congratulations, beautiful car!
Danny
Danny
96
1968 Mustang / Re: Spare Tire Trunk/Gas Tank Board
« Last post by RoyceP on May 06, 2024, 11:09:14 AM »Thanks to David Knab for the picture of the trunk board.
Although it's a minor detail, I want to install a trunk board in our 1968 Metuchen Coupe. After reading some of the associated posts, the board was intended to protect the tank from the jack (?). Can anyone tell me what the board was made of, and the dimensions? I haven't found any in supplier websites and it seems easy enough to make. I have the original trunk mat, and want to add the board.
Thanks everyone.
Bill Leonard
1968 Metuchen Coupe
8T01T225520 / 65A U 2AA 31U 16 6 1
The board appears to be made from scrap from the fabrication of the rear window filler board. I usually use originals, I don't have one to measure right now but it is around 10" by 12". The material is what I would call fiberboard, it is 1/4" thick and sold at any big box store or hardware store.
97
Drivetrain / Re: Autolite 4300 Carburetor C9ZF-F
« Last post by Bob Gaines on May 06, 2024, 10:02:37 AM »Are the MotorCraft 4300's any better???Wishful thinking I am afraid.
98
Drivetrain / Re: Autolite 4300 Carburetor C9ZF-F
« Last post by RocketScientist on May 06, 2024, 05:13:15 AM »Are the MotorCraft 4300's any better???
99
1970 Mustang / Re: 70 428CJ Question about emissions sticker
« Last post by 70cj428 on May 06, 2024, 01:51:39 AM »Digging around looking for some stuff, went thru my 70 valve covers ..... Here's the best example I have of an original emissions decal on the drivers side cover. (these covers were off a low mileage 70CJ parted out in 1983 after an accident in the mid 1970's) Every example I have (4-5 sets of covers, pics of about a dozen more) has that chunk of sticker missing over the recess for the valve cover bolt. John
100
1964 1/2 - 1965 / Re: Unusual 64.5-Early 65 Lug Wrench
« Last post by krelboyne on May 06, 2024, 01:29:59 AM »Very likely the same one(s) from my posting in reply #1 of the linked thread. I sold 5-6 ratchets to that seller.