ConcoursMustang Forums

1st Generation 1964 1/2 - 1973 - Questions & general discussions that apply to a specific year => 1969 Mustang => Topic started by: hkopp on November 20, 2012, 01:38:06 PM

Title: Help needed id'ing 2 parts
Post by: hkopp on November 20, 2012, 01:38:06 PM
These were in the glove box of my 69 Grande when I bought it in 1985 and I have no idea what they are for. I had sold the car shortly after and it sat untouched for 20 yrs, when I bought it back all the parts were still where I left them in 1987.  The large one is rubbery and has a number of C9ZB 652407 A W and has Fomoco insignia next to it with a circled IMC and a half diamond next to the C.    The one side has rounded edges, a notch on each end and a round cutout on the right.  The back is flat.

The other item looks like it should be wrapped around a harness with tape to hold the harness in place.

Any ideas?
Title: Re: Help needed id'ing 2 parts
Post by: jwc66k on November 20, 2012, 04:03:42 PM
The first one is the insert for a door pull on the driver's side.
The second is a wire harness retainer that is part of the harness to snap into a hole in a panel. The harnesses that have a woven type cloth/thread covering vs a taped covering, use and lose them often.
Jim
Title: Re: Help needed id'ing 2 parts
Post by: Brian Conway on November 20, 2012, 04:07:58 PM
The first item; C9ZB 6524047  AW  is the insert at the bottom of the Deluxe door panel cup.  Protects your finger nails and covers the screw head ?  This one is on my left door.  The one on my right door is marked C9ZB 6524046  AW with the same logos.  As to the second item; Don't know.    Brian
Title: Re: Help needed id'ing 2 parts
Post by: hkopp on November 20, 2012, 04:17:40 PM
ahah! Why didnt I notice that...well the car is now just a shell which was dismantled 27 yrs ago.  ;)  I dont have these in my other 69, guess thats why I didnt recognize them.  thanks!!
Title: Re: Help needed id'ing 2 parts
Post by: J_Speegle on November 20, 2012, 06:56:12 PM
Agree that the second item looks like a wire loom attaching clip but have not see one shaped like that (or color) used on a 69 or 70. Normally off white with a clip made of just two ears and a flat somewhat curved (to fit around the wire loom)  that is attached and tapped into the wire loom.
Title: Re: Help needed id'ing 2 parts
Post by: ClevelandKid on November 21, 2012, 06:57:38 PM
Man I need one of those C9ZB 6524047  AW door cup inserts for my Boss. I need a white one. Anyone know who has them ?
Title: Re: Help needed id'ing 2 parts
Post by: J_Speegle on November 22, 2012, 12:56:24 AM
Quote from: ClevelandKid on November 21, 2012, 06:57:38 PM
Man I need one of those C9ZB 6524047  AW door cup inserts for my Boss. I need a white one. Anyone know who has them ?

There was a point a few years back when no one had any of the white reproductions - not sure if the shortage is still on going.

Guessing you have already checked with the large places like Virgina Mustang and NPD
Title: Re: Help needed id'ing 2 parts
Post by: ClevelandKid on November 22, 2012, 10:52:32 AM
Yea I have all the catalogs and don't find a listing for them. I think there would be a demand for these as they often get lost while restoring or replacing door panels and speakers. My original door panels had them. I still have the passenger side but the drivers side came up MIA when I replaced the door panels.  >:(
Title: Re: Help needed id'ing 2 parts
Post by: J_Speegle on November 22, 2012, 03:22:21 PM
Guess they never came back once they made (reproduced) the last batch :(

Only hope now would be finding a pair used (yes I know you need only one but better find a pair ;)  or someone that purchased some for a project and never used them

Good luck with the hunt