ConcoursMustang Forums
1st Generation 1964 1/2 - 1973 - Questions & general discussions that apply to a specific year => 1970 Mustang => Topic started by: sas_302 on December 04, 2012, 01:19:10 AM
-
Does anyone have pictures of the wire harness feed to the solenoid along the firewall and around the passenger apron? Just need a reference point, mine looks too high.
Thanks,
Scott
-
I'm assuming your needing it for a 69 Mustang? I can get you some pics here later today of our original 69 Mach 1, up early right now,,,,couldn't sleep.
-
Here's some photos. Feb/69 NJ built. This is the wiring from the solenoid(original solenoid,I might add,regulator isn't), it drops down and goes under the battery then along the radiator support. the pig tail plug goes to the alternator.
This is the original wiring in its original factory location.
No wires run around the shock tower....Hope this helps.
-
Sorry guys, to clarify it is a '70 Dearborn. This section of the harness runs along the firewall above the heater motor and around the passenger apron. Try for pics again?
Thanks,
Scott
-
Makes you wonder why such a big wire routing change from a 69 NJ built Mustang and a 70 Dearborn Mustang for the solenoid? Ford usually tries to keep things simplified. Seems like alot of work to me for a part that does the same thing for either year/plant.
I know what some of you are already thinking, "It's two seperate plants at two seperate time periods". But, it's still basic with the same design under the hood(actually identical, from a sheetmeatal standpoint). Looks like communication with the design department to the supplier(s) would've kept it the same, and, that keeps the cost down......Just my thoughts, it's always intriguing to the mind.
-
Actually, there was a major change in wiring under the hood between 69 and 70. Only in 1970, the main power leads and connectors for the alternator were on the underdash harness, which snaked around the passenger side to the starter solenoid. Included in this bundle were the I and S slip-on connectors. All other years, the connections for the starter solenoid and the alternator were on the headlight harness, which came from the radiator support area to the starter solenoid.
-
Connectors and cable placement were what I was looking for. If no pics, maybe a good verbal description?
Thanks,
Scott
-
Actually, there was a major change in wiring under the hood between 69 and 70. Only in 1970, the main power leads and connectors for the alternator were on the underdash harness, which snaked around the passenger side to the starter solenoid. Included in this bundle were the I and S slip-on connectors. All other years, the connections for the starter solenoid and the alternator were on the headlight harness, which came from the radiator support area to the starter solenoid.
That's Good information to know,Thanks. I'd say that had a little to do with the ignition switch being on the steering column in '70?
-
Not really, because the wires could have been routed through the headlight harness if they wanted to. I believe it was done to improve reliability, but someone forgot that wiring exposed to engine heat tend to break down faster. It was cheaper to replace a headlight harness than an underdash harness when the wiring portion in the engine compartment deteriorated. This created more reliability issues for Ford (for maintenance and warranty issues) than if they just left the interface to the starter solenoid on the headlight harness.
Why do I think this? The configuration used was unique to 1970 and abandoned the next year. Further, Ford went to a fusible link for the main power in 71 as well, probably to decrease warranty costs (quicker, easier, and cheaper to replace a fusible link than an entire headlight harness).
-
i would like to see pics, im pretty sure my are the originals, i will take some pics and try to post here, had it figured out how to do that awhile ago. mine ws dearborn 10-20-69.
-
After scrolling through a few threads, I came across this one (5th picture down):
http://www.concoursmustang.com/forum/index.php?topic=5366.0 (http://www.concoursmustang.com/forum/index.php?topic=5366.0)
Now I see that I was wrong. Instead of across the firewall and around the apron, it is held in place with clips down the shock tower brace and to the solenoid. No wonder it seemed "misplaced" with my routing.
To Midlife's point, this would seem to be a horrible routing especially hanging in place close to the engine and over the exhaust manifold.
Anyone have a harness routing that differs from this?
Scott
-
........... Instead of across the firewall and around the apron, it is held in place with clips down the shock tower brace and to the solenoid. No wonder it seemed "misplaced" with my routing.
Anyone have a harness routing that differs from this?
Well first I guess someone didn't ask when and where your car was built. What you found might be correct for that car and engine combination but not yours.
So to that end when and where was your car built - along with what engine and trans ?
With that others (and I ) can at least offer other examples or likely routing and hardware ;)
-
Well first I guess someone didn't ask when and where your car was built......
In his 2nd post, he did mention '70 Dearborn, but he didn't mention the Month,engine or trans.
-
Missing information: Build Dearborn February 70, V8, 4sp Transmission.
I do appreciate the help with a potential variant.
Thanks,
Scott
-
Missing information: Build Dearborn February 70, V8, 4sp Transmission.
Thanks - so in the #160,000 range ;)
Looking at a few hundred cars it appears that the round plastic clips that attached the passenger side wire loom didn't hold up well and at this point allot of people have just left it to rest against the heater hoes or they have been pulled reward back into the corner to rest on the brake line - and normally no longer in the upper shock tower wire retainer. Since there is no provision for a wire loom retainer (or two ;) in the back corner its apparently IMHO that this was likely not the original location. Do have a few examples where the round (preformed circle) style of clips were inserted from the bottom of the shock tower brace/support on the passenger side.
Hope this helps
-
Unrestored '70 Dearborn Cobra Jet car I took some pictures of several years ago (not mine);
-
Yep, that's it Jeff. It was pulled back into the corner as you surmised (word of the day). My harness is not held in place in the corner but it did have a rubber coated metal hanger under one of the heater assembly nuts that the harness ran through. It then went through a plastic strap-type hanger pushed through the engine side of the shock tower. From there, it is a bit of a stretch to get to the starter solenoid.
Another mystery solved by those darn meddling kids. ;D
Scott
-
Great pic Rockhouse.
Does the cloth tape wrap both power (orange) and ground wire around the motor?
Scott
-
Unrestored '70 Dearborn Cobra Jet car I took some pictures of several years ago (not mine);
Saw a number of unrestord cars with similar holders - some all plastic some complete loops and others open like the one in the picture (looks like a vacuum hose holder from a AC equipped car) Seeing all the different retainers lead me to believe these were po fixes as mentioned.
Just me ;)
Does the cloth tape wrap both power (orange) and ground wire around the motor?
Paper based tape no cloth. Its thought (evidence based) that both wires were held to the motor as it was inserted through the hole then the wires were pulled away and attached to the other wires leaving a small tear in the tape