« previous next »
Pages: [1]   Go Down

Author Topic: WTB: 65 driver side standard 289 valve/rocker cover  (Read 1046 times)

Offline CharlesTurner

  • Charles Turner
  • Administrator
  • Hero Member
  • *****
  • Posts: 7743
WTB: 65 driver side standard 289 valve/rocker cover
« on: May 07, 2020, 11:54:30 AM »
Looking for a LH side valve cover for a '65 289.  The '65 version does not have notches for smog tubes along the bottom edge.  Can trade for one if notches?

Will buy a pair if needed.  Prefer non-rusty/non-damaged.
Logged
Charles Turner - MCA/SAAC Judge
Concours Mustang Forum Admin

Offline Brian Conway

  • Hero Member
  • *****
  • Posts: 1623
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #1 on: May 07, 2020, 03:58:18 PM »
Charles I have a pair here in, stay at home, San Diego.  Both do have some rust, passenger side couple small dents at the rear and the drivers side is dent free.  Never seen the smog tubes ?  Can send pictures.  Brian
Logged
5RO9A GT  4 Spd Built 5/29/65
9TO2R SCJ 4 Spd Built 9/19/68
Owner Driver Mechanic
San Diego, Ca.

Offline Brian Conway

  • Hero Member
  • *****
  • Posts: 1623
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #2 on: May 08, 2020, 11:01:36 AM »
After a closer look this AM the covers I have are not suitable for your needs.  Brian
Logged
5RO9A GT  4 Spd Built 5/29/65
9TO2R SCJ 4 Spd Built 9/19/68
Owner Driver Mechanic
San Diego, Ca.

Offline CharlesTurner

  • Charles Turner
  • Administrator
  • Hero Member
  • *****
  • Posts: 7743
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #3 on: May 08, 2020, 11:04:54 AM »
Quote from: Brian Conway on May 08, 2020, 11:01:36 AM
After a closer look this AM the covers I have are not suitable for your needs.  Brian

Thanks for checking.
Logged
Charles Turner - MCA/SAAC Judge
Concours Mustang Forum Admin

Offline Bossbill

  • Hero Member
  • *****
  • Posts: 3314
  • In the middle of project hell
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #4 on: May 08, 2020, 02:43:07 PM »
You even learn things in the WTB section!

I had to look up 'T/E notches' and found it in Mannel's book on page 6F2-b.

How about that!
Logged
Bill
Concours  Actual Ford Build 3/2/67 GT350 01375
Driven      6/6/70 0T02G160xxx Boss 302
Modified   5/18/65 5F09A728xxx Boss 347 Terminator-X 8-Stack
Race        65 2+2 Coupe conversion

Offline ChrisV289

  • Hero Member
  • *****
  • Posts: 1986
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #5 on: May 08, 2020, 03:26:43 PM »
I looked as well Charles. I have a pair I am going to be using as masks when I repaint the engine but the passenger side is 65 and the driver is 66
Logged
Chris
1965 Honey Gold Fastback (SJ 10/29/64)
1965 Caspian Blue Fastback (SJ 06/03/65)
2009 V6 Mustang Coupe

Offline CharlesTurner

  • Charles Turner
  • Administrator
  • Hero Member
  • *****
  • Posts: 7743
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #6 on: May 08, 2020, 04:00:08 PM »
Quote from: ChrisV289 on May 08, 2020, 03:26:43 PM
I looked as well Charles. I have a pair I am going to be using as masks when I repaint the engine but the passenger side is 65 and the driver is 66

We have the same then, I've also been using a pair like that for masks, but now need a pair of 65's!
Logged
Charles Turner - MCA/SAAC Judge
Concours Mustang Forum Admin

Offline Hipo giddyup

  • Hero Member
  • *****
  • Posts: 1211
  • There is no end to doing right. Giddyup!!!
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #7 on: May 09, 2020, 12:31:57 PM »
Hey Charles. I was looking  around and found a pair of non-notched 65 valve covers. However, these were the over-the-counter chromed versions. Not sure if that would be any use to you? I imagine you would be stripping the chrome to make it work?
Logged
1967 Springtime Yellow Coupe, 289 2v 3spd, Metuchen built, Nov. 17th 66'
1966 Sahara Beige Coupe, 289 2v 3spd, Dearborn built, July 21st 66'
1964 1/2 Pagoda Green Coupe, 260 2v 3spd, Dearborn built, June 30th 64'
1966 GT350 Fastback clone, 289 HiPo, 725cfm Holley, 4spd, SanJose built, Nov 25th 65'

Offline OldGuy

  • Full Member
  • ***
  • Posts: 115
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #8 on: May 09, 2020, 02:11:37 PM »
Quote from: CharlesTurner on May 07, 2020, 11:54:30 AM
Looking for a LH side valve cover for a '65 289.  The '65 version does not have notches for smog tubes along the bottom edge.  Can trade for one if notches?

Will buy a pair if needed.  Prefer non-rusty/non-damaged.

Charles, I've got exactly what you asked for. PM for details.

Frank
Logged

Offline lancelot66

  • Sr. Member
  • ****
  • Posts: 301
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #9 on: May 22, 2020, 02:29:38 PM »
Logged
VR/
-Lance

SJ Build Date: 1/6
'66 Fstbk: 63A M 25 06A 71 1 6
Many Original Options

Offline CharlesTurner

  • Charles Turner
  • Administrator
  • Hero Member
  • *****
  • Posts: 7743
Re: WTB: 65 driver side standard 289 valve/rocker cover
« Reply #10 on: May 22, 2020, 02:37:24 PM »
Thanks for all the replies.  Found what was needed.
Logged
Charles Turner - MCA/SAAC Judge
Concours Mustang Forum Admin
Pages: [1]   Go Up
« previous next »