Recent Posts

11

Parts / Re: I need a new windshield, PS auto glass or ECS?

« Last post by jtfx6552 on May 18, 2024, 05:53:50 PM »

The Library article on 65 Glass goes to a dead link. My windshield has been replaced, I'm looking for information on what the date code and logo would have looked like and their location.

12

1966 Mustang / Re: C4ZE Y1 4 Speed Radiator Questions

« Last post by J_Speegle on May 18, 2024, 04:58:39 PM »

Thank you everyone.  I found a tank and it will be installed next week.

Good for you and that was quick.

13

1967 Mustang / Re: Location of Parking brake Equalizer pivot bracket

« Last post by jwc66k on May 18, 2024, 03:09:37 PM »

Go to this forums' "Library" and open "ConcoursMustang.com Official 67 Mustang Article List", then open "1965-72 Ford Master Parts Catalog" (aka MPC - it's a link to a T-Bird site that allows us to use their data), then go to the illustrated section on wheels and brakes. You want "Illustrated Section 20", page 11, where you can see the items you are interested in for a common reference. Unfortunately, there are no measurements.
Jim

14

1967 Mustang / Location of Parking brake Equalizer pivot bracket

« Last post by motor head 428 on May 18, 2024, 10:12:27 AM »

The floor pan was changed on a friends car and we are trying to get a measurement for the bracket the the Parking brake pivot bracket to the transmission crossmember. We would like to get the measurement to the center of the pin that the Parking Brake Equalizer pivots on. Thank You

15

1966 Mustang / Re: C4ZE Y1 4 Speed Radiator Questions

« Last post by JeffWS on May 18, 2024, 07:09:32 AM »

Thank you everyone.  I found a tank and it will be installed next week.

16

Parts for Sale / 390GT Exhaust Manifolds

« Last post by Azdriver on May 18, 2024, 01:22:47 AM »

Nice clean pair of manifolds   C6OE-9430-A dated 8B21 C7OE-9431-A dated 8B13. No cracks or repairs.

$450 plus shipping.

Pat

17

1968 Mustang / Re: 381863-S2 clip nut

« Last post by 67gta289 on May 17, 2024, 09:28:39 PM »

Or AMK for $32 even and that way I can order those other few bits I need.  I always seem to end up not needing $30 worth of fasteners to meet their minimum.  I wish they wouldn't do that and just fill all orders regardless of the size.  I know time is money but a sale is a sale. I'm done venting.

I get all of my AMK fasteners from NPD.  I never have any problem spending 30 buck there lol.

18

Drivetrain / Re: A Fan Of Unknown Origin -

« Last post by jwc66k on May 17, 2024, 07:22:20 PM »

Sometimes you answer your own questions. I was looking up a carburetor number for a neighbor in my "Mustang & Fords Small Block V8, 1962-1969" and found that the "Fan of Unknown Origin" is an early 64-65 standard 260-289 fan. If Bob Mannel say that's what it is, I'm satisfied.
Jim

19

1968 Mustang / Re: 381863-S2 clip nut

« Last post by jwc66k on May 17, 2024, 07:06:12 PM »

Or AMK for $32 even and that way I can order those other few bits I need.  I always seem to end up not needing $30 worth of fasteners to meet their minimum.  I wish they wouldn't do that and just fill all orders regardless of the size.  I know time is money but a sale is a sale. I'm done venting.

In this "capital" oriented, "capitalist" country of America, the "business" of "business" is to make "money". The truth does make you want to vent sometimes.
Jim

20

1968 Mustang / Re: 381863-S2 clip nut

« Last post by dkknab on May 17, 2024, 06:36:16 PM »

NPD - AMK Guide is listed under their stock number L-41, $32.86. It's the third edition.
Jim

Or AMK for $32 even and that way I can order those other few bits I need.  I always seem to end up not needing $30 worth of fasteners to meet their minimum.  I wish they wouldn't do that and just fill all orders regardless of the size.  I know time is money but a sale is a sale. I'm done venting.